ASTM A335 P91 Pipe

ASTM A335 P91 Pipe

Details
ASTM A335 P91 seamless pipe (9Cr-1Mo-V) for ultra-supercritical boilers and high energy piping. China mill with full heat treatment records, hardness control and third-party inspection.
Category
Carbon Steel Pipe
 
Send Inquiry
Description
Technical Parameters

ASTM A335 P91 seamless alloy steel pipe for supercritical boiler

图注:A335 P91 无缝管,9Cr-1Mo-V,正火加回火,硬度控制 250 HB 以下

ASTM A335 P91 is the grade that made ultra-supercritical power plants economic. Nine percent chromium with molybdenum and a controlled vanadium-niobium addition gives roughly three times the creep strength of P22, which lets designers use thinner walls, lower weight and higher steam temperatures around 600 degrees C. It is also the most metallurgically unforgiving pipe grade in common supply: the heat treatment window is narrow, hardness must be controlled tightly, and a mill that treats P91 like P22 produces pipe that meets the certificate and fails in service. This page sets out what the grade demands and how to buy it without inheriting that risk.

Why P91 Is Different Metallurgically

The strength comes from a tempered martensitic microstructure. Pipe is normalised at about 1040-1080 degrees C, then tempered at 730-780 degrees C, and the result is a structure that resists creep at 600 degrees C but loses toughness if tempering is skipped or rushed. Three practical consequences follow. Cooling after normalising must be fast enough to form martensite - thick wall sections sometimes need forced cooling, and a mill without that capability will quietly produce bainite. Tempering temperature must be controlled within a narrow band; too low leaves hardness above the limit, too high collapses creep strength. And the pipe must never be stress relieved or welded without matching procedures, because P91 is sensitive to Type IV cracking in the fine-grained heat-affected zone.

Specification Numbers Buyers Must Check

ItemA335 P91 requirementWhy it matters
Chromium8.00 - 9.50 percentOxidation and creep resistance
Molybdenum0.85 - 1.05 percentSolid solution strengthening
Vanadium0.18 - 0.25 percentPrecipitate strengthening
Niobium0.06 - 0.10 percentGrain refinement
Nitrogen0.030 - 0.070 percentNitride formation, needs control
Min yield strength415 MPaDesign basis
Tensile strength585 MPa minimumCertification
Hardness250 HB max typically specifiedAcceptance after tempering and PWHT
Heat treatmentNormalise 1040-1080 C, temper 730-780 CMust appear as parameters, not "as treated"

Ask for the actual normalising and tempering temperatures on the certificate, not a statement that heat treatment was performed. A P91 certificate without parameters cannot be audited and is the single strongest warning sign in this product category. Second, ask for hardness traverses on heavy wall sections, where cooling rate varies through the thickness and the bore can miss the target structure.

P91 vs P22 vs P11: What the Numbers Mean for a Project

P91 carries about 415 MPa yield against 205 MPa for P11, but the real difference is creep rupture strength at 600 degrees C, where P91 offers roughly three times the life of P22 at the same stress. That is what allows a supercritical boiler to run 100 degrees C hotter without thickening every wall. The cost ladder is steep - P91 runs two to three times P11 per ton before welding and heat treatment - so the grade is chosen by design temperature and pressure, never by availability. For plants in the 540 degrees C band, P11 or P22 remain the economical choice; P91 appears when the cycle efficiency target cannot be reached otherwise.

Fabrication and Welding Reality

Most P91 problems appear after delivery, in fabrication. Welding requires preheat around 200-250 degrees C, controlled interpass temperature, matching consumables and post-weld heat treatment at 750-770 degrees C with accurate thermocouple placement. Grinding or gouging must avoid overheating, and any field weld should be hardness tested across the HAZ rather than at the cap only. Buyers who are new to the grade should insist that the fabricator submit welding procedure specifications for review before production starts; retrofit repairs on a header after hydro test are the expensive way to learn. Our A335 P11 page covers the lower rungs of the same ladder, and ambient-temperature lines in the same plant run on seamless carbon steel pipe.

Supply Programme

We supply A335 P91 in 1/2 to 24 inch OD, SCH 40 to SCH XXS, seamless, normalised and tempered, with EN 10204 3.1 certification including heat treatment parameters, tensile and hardness results. Optional extras include ultrasonic examination of the full body, hardness traverse reports on heavy walls, and third-party witness inspection. Lead time is 5-8 weeks depending on wall thickness and test scope, because thick-wall P91 heat treatment is scheduled rather than continuous. If your project has a boiler erection date, share it at inquiry - the grade has fewer qualified mills than carbon steel, and schedule is where most P91 orders slip. Line lists go through our contact page.

Related pages: ASTM A333 Grade 6 pipe for low temperature lines, and the carbon steel pipe category for the full range.

Frequently Asked Questions

How do I verify P91 heat treatment from a certificate? Read the normalising and tempering temperatures and check they sit in the 1040-1080 C and 730-780 C windows, then check hardness values against the project limit. If the certificate states only "normalised and tempered" without numbers, request the heat treatment chart - a mill that ran the cycle can produce it.

Can P91 pipe be bent or hot formed on site? Hot forming above the lower critical temperature destroys the tempered martensite and requires full re-heat treatment afterwards. Cold bending is possible within limits, followed by stress relief. Either way the forming procedure belongs in the approved method statement, not in a site instruction on the day.

Is P91 available in welded pipe? A335 P91 is supplied seamless in our programme. Welded 9Cr pipe exists under other specifications and is used for large-diameter headers in some designs, but it should never be offered as A335 P91 without written approval - the specification and the inspection regime differ.

 

Hot Tags: astm a335 p91 pipe, p91 seamless pipe, astm a335 p91 pipe china supplier, 9cr 1mo v alloy pipe, p91 pipe price

Send Inquiry
Have a Question? Get in Touch.

Whether you need product information, technical support, or a steel supply quotation, our team is ready to assist you.
Contact us by phone, email, or the inquiry form, and we will get back to you as soon as possible.

Contact now!