EN 10219 and ASTM A500 both cover cold-formed welded hollow sections, and at first glance the grades line up: S355J2H and A500 Grade C are both roughly 350 MPa yield. The difference that matters is that EN 10219 requires impact testing as part of the grade, and A500 does not.
That single structural difference decides which standard a project can accept - and it is why the two are not interchangeable on structures that must absorb energy or perform at low temperature.
What Each Standard Actually Covers
EN 10219 is published in two parts: Part 1 sets the technical delivery conditions, Part 2 sets tolerances, dimensions and sectional properties. It covers cold-formed welded circular, square, rectangular and elliptical hollow sections, in steel grades from S235 to S460, with optional impact testing at 0°C or −20°C encoded in the grade suffix.
ASTM A500 covers cold-formed welded and seamless carbon steel structural tubing in round, square and rectangular shapes. It specifies mechanical properties by grade - A, B, C, D - and deliberately leaves chemistry open, on the basis that the tube producer may use whatever steel satisfies the mechanical requirements.
That contrast is the core of it: EN 10219 controls chemistry and toughness as well as strength; A500 controls strength and lets the producer choose the chemistry.
Grade Comparison
| EN 10219-1 grade | Yield ReH (MPa) | Tensile Rm (MPa) | Impact | A500 nearest grade | Yield (MPa) | Tensile (MPa) | Impact |
|---|---|---|---|---|---|---|---|
| S235JRH | 235 | 360 – 510 | 27 J @ 20°C | A500 Gr A | 269 (39 ksi) | 400 (58 ksi) | Not required |
| S275J0H | 275 | 430 – 580 | 27 J @ 0°C | A500 Gr B | 290 (42 ksi) | 400 (58 ksi) | Not required |
| S275J2H | 275 | 430 – 580 | 27 J @ −20°C | A500 Gr B | 290 (42 ksi) | 400 (58 ksi) | Not required |
| S355J0H | 355 | 470 – 630 | 27 J @ 0°C | A500 Gr C | 317 (46 ksi) | 427 (62 ksi) | Not required |
| S355J2H | 355 | 470 – 630 | 27 J @ −20°C | A500 Gr C | 317 (46 ksi) | 427 (62 ksi) | Not required |
| S420MH | 420 | 500 – 660 | As agreed | - | - | - | - |
| S460MH | 460 | 530 – 690 | As agreed | - | - | - | - |
EN values quoted for wall thickness ≤ 16 mm; yield falls for heavier wall. A500 values are minimum specified, converted from ksi. "H" in the EN grade denotes hollow section; "M" denotes thermomechanical rolling.
The apparent mismatch in strength - A500 Grade C at 317 MPa against S355 at 355 MPa - is real but narrower in practice, because A500 specifies minimum values while EN specifies a range that includes measurement scatter. The 38 MPa gap is nonetheless enough that a member designed to S355 cannot simply be built from A500 Gr C.
Impact Testing: The Decisive Difference
EN 10219 grades ending in J0 or J2 carry a mandatory Charpy V-notch requirement - 27 joules absorbed at 0°C or −20°C respectively. The test is part of the grade; you cannot claim S355J2H without producing the results.
A500 has no impact requirement in the base specification. A purchaser who needs toughness must invoke a supplementary requirement, and those supplements are less commonly exercised, which means fewer mills hold routine data for them.
Where this matters:
- Seismic design. Members expected to yield in a seismic event need toughness to avoid brittle fracture at connections. EN grades with J2 are straightforward to specify; A500 requires the supplement.
- Cold climate. Below roughly −10°C service temperature, Charpy energy at the service temperature becomes a design input, not a formality.
- Dynamic and fatigue-loaded structures. Crane jibs, conveyor gantries, stadium roofs.
Tolerances And Dimensions
EN 10219-2 is more prescriptive than A500 on the details that affect fabrication:
| Parameter | EN 10219-2 | ASTM A500 |
|---|---|---|
| Outside dimension | ±1% (CHS), ±1% min ±0.5 mm (RHS/SHS) | ±0.5% round, ±0.5% flat sides |
| Wall thickness | ±10% for thickness ≥ 5 mm | ±10% |
| Corner radius | Specified by range | Specified, up to 3× wall |
| Straightness | 0.2% of length | 0.15% of length |
| Squareness of section | 90° ± 1° | 90° ± 2° |
| Mass tolerance | −6% / +10% per bundle | −3.5% / +10% per piece |
For fabrication, the practical difference is that A500 allows slightly more out-of-square and less mass variation per piece, while EN holds squareness tighter. Neither is better in the abstract; a fabricator set up for one will notice the other.
Which Standard Applies Where
Use EN 10219 when the project is designed to Eurocodes, when impact toughness must be demonstrated, when the specification already references S355J2H, or when the structure sits in a cold or seismic region. It is the default across Europe, the Middle East on European-designed projects, and much of Southeast Asia on consultant-led work.
Use ASTM A500 when the project is designed to AISC or similar US codes, when the supply chain is North American, or when the structure is static, indoor and warm - where the absence of a Charpy requirement costs nothing. Grade C is the common structural grade; Grade B appears in lighter sections.
Where a project specifies both - increasingly common on international work - the resolver is usually "EN 10219 S355J2H, or A500 Grade C with Charpy supplement at −20°C". That is a genuine equivalence and can be quoted both ways.
Frequently Asked Questions
Is S355J2H equivalent to A500 Grade C?
Close on strength, not equivalent on specification. S355J2H is slightly stronger and carries a mandatory −20°C impact test. A500 Grade C has lower minimum yield and no impact requirement unless supplemented.
Can A500 be substituted for EN 10219 on a European project?
Only with the designer's approval and usually only with an impact-test supplement plus a chemistry declaration. The base A500 certificate does not demonstrate what EN 10219 requires.
What does the "H" mean in S355J2H?
Hollow section. The suffix distinguishes the grade from plate or bar of the same strength (S355J2), because hollow sections are cold formed and their properties differ from hot rolled product.
Are hollow sections always cold formed?
No. Both standards cover cold-formed welded tube, but hot finished hollow sections exist under EN 10210, with different residual stress and tolerance characteristics. EN 10210 and EN 10219 are not interchangeable in a design.
Ordering Structural Hollow Sections
We produce welded carbon steel hollow sections to both EN 10219 and ASTM A500, in S235JRH through S355J2H and A500 Grades A to C, square, rectangular and circular, with mill certificates and impact test results where the grade requires them.
If your specification names one standard and your fabricator prefers the other, send both and we will quote the equivalent, stating exactly which properties are matched and which are not. The wider carbon steel pipe range covers line pipe and process pipe to ASTM A53 as well.
Send your section size, grade and standard - we reply with price, tolerance confirmation and certificate scope.
