Z120 and Z275 are not grades and not quality levels - they are coating masses. Z120 means 120 g/m² of zinc applied across both faces, which is 60 g per square metre per side, or about 8.4 µm of zinc.
That conversion is the whole subject. Once coating mass is expressed in microns, it can be compared against a corrosion rate for the actual environment, and the choice between Z120 and Z275 becomes a service-life calculation rather than a preference.
Reading The Designation
The number after Z is the total zinc mass on both surfaces, in grams per square metre, measured to EN 10346. Because the coil is coated on both faces, the mass per face is half the designation - a point that causes frequent confusion when a buyer compares a "Z275" quote against a "137 g/m²" specification and assumes they differ.
| Designation | Total both faces (g/m²) | Per face (g/m²) | Zinc thickness per face | ASTM A653 equivalent |
|---|---|---|---|---|
| Z100 | 100 | 50 | ≈ 7 µm | G30 (90 g/m²) |
| Z120 | 120 | 60 | ≈ 8.4 µm | G40 (120 g/m²) |
| Z180 | 180 | 90 | ≈ 12.6 µm | G60 (180 g/m²) |
| Z275 | 275 | 137.5 | ≈ 19.3 µm | G90 (275 g/m²) |
| Z350 | 350 | 175 | ≈ 24.5 µm | G115 (350 g/m²) |
Conversion: zinc density is 7.14 g/cm³, so 1 g/m² corresponds to approximately 0.14 µm of coating. Values are nominal; EN 10346 permits a minimum single-spot mass below the triple-spot average.
From Microns To Years
Zinc protects steel by sacrificial action: it corrodes in preference to the steel beneath, and the coating thickness determines how long that protection lasts. Zinc consumption depends almost entirely on the environment:
| Environment | Zinc loss per year | Z120 (8.4 µm) life | Z275 (19.3 µm) life |
|---|---|---|---|
| Indoor, dry, heated | < 1 µm | Decades | Decades |
| Rural / low pollution outdoor | ≈ 1 µm | 8 – 10 years | 18 – 22 years |
| Urban / industrial | 2 – 3 µm | 3 – 5 years | 7 – 10 years |
| Coastal, within 1 km of sea | 4 – 8 µm | 1 – 2 years | 2 – 5 years |
These are order-of-magnitude figures for first red rust, drawn from standard atmospheric corrosion classifications. They are the reason a Z275 specification that looks generous inland becomes marginal on a coastal roof - and why coating choice cannot be made from the price list alone.
Two modifiers shorten life beyond the table: cut edges, where the zinc is absent and protection relies on sacrificial throw, which is limited to a few millimetres; and formed crevices where moisture sits.
What The Heavier Coating Costs You
Z275 is not simply better. Three penalties come with the extra zinc:
- Price. The zinc itself is the cost: expect roughly 8–15% above Z120 for the same base steel, tracking the zinc market.
- Formability. A thicker coating cracks at tighter bend radii and can flake at sheared edges. Deep-drawn parts normally specify a lighter coating, sometimes with a differential coating - heavier on the exposed face, lighter on the hidden one.
- Welding. More zinc means more fume, more porosity at the weld and more post-weld cleaning. Resistance welding of Z275 needs higher electrode force and shorter electrode life than Z120.
There is also a surface question: heavier coatings show a more pronounced spangle, which matters if the coil will be painted without a levelling primer, or used where a uniform appearance is specified.
Choosing Between Them
The decision sequence that holds up in specification review:
- Define the exposure. Indoor, rural, industrial, coastal, or in contact with a specific chemical. This alone separates most cases.
- Set the design life - typically 10, 20 or 25 years for building products.
- Divide life by the corrosion rate to get the required zinc thickness, then double it for the two faces and convert back to a designation.
- Check the forming. If the part is bent or drawn beyond a modest radius, the coating that the corrosion calculation asked for may not survive the press. In that case the answer is often a lighter coating plus a paint system, not a heavier coating.
For interior partitions, ducting, furniture frames and enclosed structures, Z120 is normally correct and specifying Z275 wastes money. For roofing, wall cladding, exposed framing and anything within a few kilometres of the coast, Z275 is the realistic minimum - and near the coast, Z275 plus a paint system is the practical answer.
Related Specification Points
Coating mass is one of four things to fix on a galvanized coil order. The others:
- Base steel grade - DX51D is the common commercial-quality designation for bending and profiling; DX52D and DX53D for deeper drawing.
- Surface treatment - chromate-free passivation, oiling, or anti-finger print. This decides whether the coil can be stored before use without white rust.
- Spangle - regular, minimised or skin-passed. Skin-passed (SP) improves flatness and paint adhesion, and is specified whenever the surface will be visible or coated.
Frequently Asked Questions
Is Z275 the same as G90?
Effectively yes. ASTM A653 G90 specifies 0.90 oz/ft² total on both faces, which converts to approximately 275 g/m² - the same coating mass under a different standard.
What is the difference between Z120 and Z275 in microns?
About 8.4 µm per face against 19.3 µm per face - roughly 2.3 times the coating thickness.
Can Z120 be used outdoors?
For a few years in a mild environment, yes. For a permanent outdoor structure it is usually under-specified; the first red rust appears before the paint maintenance cycle is due.
Does a heavier coating mean better paint adhesion?
No. Paint adhesion depends on surface preparation and on whether the coil is skin-passed and passivated, not on coating mass. A thick coating with poor pretreatment performs worse than a thin one properly prepared.
Ordering Galvanized Coil
We supply DX51D galvanized coil from Z100 to Z350, in thickness 0.2–3.0 mm and widths up to 1,500 mm, hot dip galvanized on a continuous line with passivation, oiling or anti-finger treatment to order.
For heavier coatings or thicker sections, see our hot dipped galvanized coil range, and the full galvanized steel coil page for available combinations.
Send your coating mass, base grade and quantity - we will confirm the coating tolerance, surface treatment and delivery date in one reply.
