304 vs 316 Stainless Steel Pipe: Chloride, Cost & Selection

Oct 29, 2026

Leave a message

304 and 316 are the same alloy family separated by one addition: 2–3% molybdenum. That single element decides whether the pipe survives a chloride environment, and it accounts for roughly a third of the price difference.

Because the visible difference is nil - both are austenitic, non-magnetic and look identical - the choice has to be made on the service environment, not on the sample. This comparison sets out what the molybdenum actually does and where each grade stops being the right answer.

Chemistry: What Actually Differs

Both grades are austenitic stainless steels built on an 18/8 chromium-nickel base, with the carbon content limited to keep welds ductile. The differences are small in percentage terms and large in effect:

Element304 / 304L316 / 316LEffect
Chromium18.0 – 20.0%16.0 – 18.0%Forms the passive oxide layer
Nickel8.0 – 11.0%10.0 – 14.0%Stabilises the austenitic structure
Molybdenum-2.0 – 3.0%Resists pitting and crevice attack
Carbon (standard)0.08% max0.08% maxStrength; sensitisation risk in welds
Carbon (L grade)0.035% max0.035% maxPrevents sensitisation at weld zone

Note that 316 carries less chromium than 304 and more nickel. On chromium alone, 316 would be the weaker grade in oxidising conditions. The molybdenum more than compensates in chloride service, which is the trade the grade is designed around.

PREN: Putting A Number On The Difference

Pitting Resistance Equivalent Number combines the three elements that resist chloride attack into a single figure:

PREN = %Cr + 3.3 × %Mo + 16 × %N

GradeTypical PRENChloride guidelineService note
304 / 304L≈ 18Up to ~200 mg/L at ambientFresh water, food, architectural
316 / 316L≈ 24 – 26Up to ~1,000 mg/L at ambientMarine atmosphere, chemical, process
2205 duplex≈ 34 – 36Above 3,000 mg/LBrine, offshore, high chloride + high strength

These chloride figures are design guidance, not limits in a standard. Pitting depends on temperature, oxygen level, stagnation and surface finish as much as on concentration - a 304 line carrying 150 mg/L at 20°C may be fine, and the same line at 60°C with deposits may pit.

Temperature Is The Hidden Variable

Chloride resistance falls as temperature rises, and much faster for 304 than for 316. The practical consequence is that a specification written for ambient conditions can fail in a hot line even though the chloride level never changed.

Two temperature issues matter beyond pitting:

  • Sensitisation, 425–860°C. Chromium carbide precipitates at grain boundaries and depletes the adjacent metal of chromium, leaving it open to intergranular attack. Welding puts the heat-affected zone right in this range - which is why 304L and 316L are specified for welded pipe rather than the standard carbon grades.
  • Chloride stress corrosion cracking. Above roughly 60°C, both grades become susceptible under tensile stress in chloride service. Moving from 304 to 316 delays but does not eliminate it; duplex or a change of material family is the real answer.

Both grades oxidise in air to around 870–925°C in continuous service. Where creep strength above 500°C matters, 316 holds up better - its molybdenum and higher nickel improve high-temperature performance, not just corrosion resistance.

Cost: Where The Third Comes From

316 typically costs 30–45% more than 304 for the same size and wall. The gap is driven by two alloying elements that are priced on their own markets: molybdenum, which is expensive and volatile, and nickel, which 316 contains more of.

Because the price difference is driven by raw material, it moves. When nickel and molybdenum are high, the gap widens; when they fall, it narrows. A comparison quote dated six months ago is not a reliable basis for a current decision.

Weight matters as much as grade. Stepping down a wall thickness in 316 can cost less than the 304 equivalent - but only if the pressure rating still works, which requires the calculation, not the price list.

Selection Rules That Hold Up

In order of frequency in real specifications:

  1. Coastal or marine exposure, outdoor, unpainted - 316. Salt deposition is enough to pit 304 on a slow timeline, and the staining shows before the failure does.
  2. Food, beverage, dairy, pharmaceutical - 304L is usually sufficient because the media are chloride-free and cleaning is controlled. 316L is specified where chlorinated cleaning agents or brine are present.
  3. Chemical process with chlorides, or any acid service - 316L as the starting point, with the specific medium checked against a corrosion table. Neither grade suits hydrochloric acid at any useful concentration.
  4. High-temperature lines above 500°C - 316 or a higher grade, on creep strength grounds rather than corrosion.
  5. Indoor architectural, potable water, general fabrication - 304 is the economical answer and over-specifying it wastes money without buying life.

Frequently Asked Questions

Can I use 304 instead of 316 to save cost?

Only if the service is chloride-free and stays below the temperature where pitting starts. In a coastal or chlorinated environment, 304 will pit and the repair cost exceeds the saving - often within two or three years.

What is the difference between 316 and 316L?

Carbon content: 0.08% maximum against 0.035%. The L grade resists sensitisation in the weld heat-affected zone and is the normal choice for welded pipe. Its slightly lower strength is rarely the governing factor in piping design.

Is 316 magnetic?

No, in the annealed condition both 304 and 316 are austenitic and effectively non-magnetic. Cold drawing can induce slight magnetism in either grade, so a magnet is not a reliable grade test.

How do I confirm the grade after delivery?

Positive material identification with an X-ray fluorescence analyser will show chromium, nickel and molybdenum, and molybdenum is the discriminator: a reading near zero means 304, 2–3% means 316. Ask for PMI on a sample of the shipment rather than relying on the stencil.

Ordering Stainless Steel Pipe

We supply 316 and 316L stainless steel pipe and 304/304L in seamless and welded construction, from 1/2" to 24", with mill certificates and PMI reports. The full range is on our stainless steel pipe page.

If the service involves chlorides above the figures in this table, tell us the concentration and temperature and we will quote duplex as well, so the comparison is like for like on life rather than on first cost.

Send your grade, size and medium for a quotation - we reply with price, delivery and the certificate package included.

Send Inquiry
Have a Question? Get in Touch.

Whether you need product information, technical support, or a steel supply quotation, our team is ready to assist you.
Contact us by phone, email, or the inquiry form, and we will get back to you as soon as possible.

Contact now!